漏電起痕試驗儀采用矩形鉑電極，兩極對試樣的作用力分別為1.0N±0.05N。施加電壓在100～600V(48～60Hz)之間可調，短路電流在1.0±0.1A時，電壓下降應不超過10%，當試驗回路中，短路漏電電流等于或大于0. 時，時間維持2秒鐘，繼電器動作，切斷電流，指示試件不合格。滴液裝置時間常數可調，控制滴液量大小44～50滴/cm3和滴液時間間隔30±5秒。符合GB/T4207-2012固體絕緣材料耐電痕化指數和相比電痕化指數的測定方法、GB/T3048.7-2007電線電纜電性能試驗方法第7部分：耐電痕試驗等試驗標準

漏電起痕試驗儀在操作過程中要注意的事項：

1、漏電起痕試驗儀在操作過程中，人員應該注意個人防護，避免漏電受傷或被溶液沾染到口、眼部位造成傷害

2、輸入電源AC220±2%。

3、排氣管應通出窗外。

4、在對樣品進行時,請勿打開倉門,待試驗完之后或當實驗失效產生火煙時，先打開風扇排除煙霧后，再打開倉門進行作業。

5、實驗前須確認設備是否在計量有效期內，如超期則不能進行實驗

6、電源應用有地線的三極插座，保證接地可靠